4個獨立充電插槽，可各別為 1 到4 顆 3號AA、4號AAA鎳氫充電池充電與分析。
Four independent slots
It's like having four charger-analyzers for AA and AAA NiMH / NiCD batteries.
LCD液晶顯示具LED背光照明 Large backlit LCD display
4個獨立LCD液晶數位顯示 (充電流 / 電池容量 / 充電時間 / 電池電壓..資訊)一目瞭然 Digitally displays capacity, voltage, time and current.
無盡的編程可能性-超過10000種方法！ Endless programming possibilities - over 10,000 ways!
29種電流 29 selectable charging and discharging rate. Charging current from 0.2A to 2.0A and discharging current from 0.1A to 1.0A in 0.1A increments.
可於於200mA 和 2000mA 之間自行選擇設定19 種充電電流。
可於於100mA 和 1000mA 之間自行選擇設定10 種放電電流。
Five modes of operation 五種模式
Charge： Recharges the battery at the selected rate.
Suitable for batteries used frequently.
Refresh & Analyze： Charges the battery, rest for one hour, discharge, rest again, then recharges it. Selectable charging and discharging rate.
Suitable for batteries stored for more than two weeks but less than 3 month or those showing poor performance.
Break-In： Also known as IEC capacity measurement and "Battery Forming". Charges battery at 0.1C for 16 hours, rest for one hour, discharges battery at 0.2C, then recharges again at 0.1C for 16 hours.
Suitable for new batteries and those stored for more than 3 month.
Discharge： Discharges the battery at the selected rate.
Cycle： Performs charge-discharge cycle for up to 12 times with discharge capacity stored in memory. Recharges battery after final cycle.
New ways to take care of your batteries and maximize runtime!
In most devices, usually two or more batteries are used together. When batteries are used in a series, the performance is limited by the worst one. In other words, one poorly performing battery can significantly reduce the device runtime.
Battery matching refers to grouping batteries with similar 贈ctual?capacity. To perform this, use the Refresh & Analyze mode to determine the battery capacity. Group batteries with capacity within about +/- 5% of the rated capacity.
New batteries and those stored for extended period become chemically deactivated. Battery forming is a charge-discharge-charge cycle which forces a full charge into the battery at a very slow rate. This process activates the battery. In certain cases, it needs to be repeated two or three times.
Battery forming can be performed using the Break-In mode.
Delivers just the right charge
Independent negative delta V, temperature and timer protection eliminates over and undercharging.
Super light travel worldwide power supply and 12V compatible
Worldwide 100-240V switching adapter - light weight and small. Also compatible with 12V input. Will work on car when used with the optional cigarette lighter adapter.
飽和充電電流： 100mA / 涓流充電電流： 10mA
Charging Current： Programmable from 0.2A to 2.0A in increments
Topoff Charging Current： 100mA
Maintenance Charging Current： 10mA
Discharge Termination： Voltage 1.00V
Discharge Current： Programmable from 0.1A to 1.0A in increments of 0.1A
Capacity Storage Memory： 12 (Cycle mode only)
精準微處理器可支援電池容量Supported Capacity： 100 to 20,000mAh.
Charger Input Power： 12V 2.0A
輸入電壓 Adapter Input： 100-240V 50/60Hz
原廠中文使用說明 =>( 中文使用說明按這裡 )